IPv4

Internet protocol suite
Application layer
BGP DHCP DNS FTP HTTP HTTPS IMAP LDAP MGCP MQTT NNTP NTP POP ONC/RPC RTP RTSP RIP SIP SMTP SNMP SSH Telnet TLS/SSL XMPP more...
Transport layer
TCP UDP DCCP SCTP RSVP more...
Internet layer
IP IPv4 IPv6 ICMP ICMPv6 ECN IGMP IPsec more...
Link layer
ARP NDP OSPF Tunnels L2TP PPP MAC Ethernet Wi-Fi DSL ISDN FDDI more...

Internet Protocol version 4 (IPv4) is the fourth version of the Internet Protocol (IP). It is one of the core protocols of standards-based internetworking methods in the Internet and other packet-switched networks. IPv4 was the first version deployed for production in the ARPANET in 1983. It still routes most Internet traffic today, despite the ongoing deployment of a successor protocol, IPv6. IPv4 is described in IETF publication RFC 791 (September 1981), replacing an earlier definition (RFC 760, January 1980).

IPv4 uses a 32-bit address space, which limits the number of unique hosts to 4,294,967,296 (2³²), but large blocks are reserved for special networking methods.

Purpose

The Internet Protocol is the protocol that defines and enables internetworking at the internet layer of the Internet Protocol Suite. In essence it forms the Internet. It uses a logical addressing system and performs routing, which is the forwarding of packets from a source host to the next router that is one hop closer to the intended destination host on another network.

IPv4 is a connectionless protocol, and operates on a best effort delivery model, in that it does not guarantee delivery, nor does it assure proper sequencing or avoidance of duplicate delivery. These aspects, including data integrity, are addressed by an upper layer transport protocol, such as the Transmission Control Protocol (TCP).

Addressing

Decomposition of the quad-dotted IPv4 address representation to its binary value

IPv4 uses 32-bit addresses which limits the address space to 4294967296 (2³²) addresses.

IPv4 reserves special address blocks for private networks (~18 million addresses) and multicast addresses (~270 million addresses).

Address representations

IPv4 addresses may be represented in any notation expressing a 32-bit integer value. They are most often written in dot-decimal notation, which consists of four octets of the address expressed individually in decimal numbers and separated by periods.

For example, the quad-dotted IP address 192.0.2.235 represents the 32-bit decimal number 3221226219, which in hexadecimal format is 0xC00002EB. This may also be expressed in dotted hex format as 0xC0.0x00.0x02.0xEB, or with octal byte values as 0300.0000.0002.0353.

CIDR notation combines the address with its routing prefix in a compact format, in which the address is followed by a slash character (/) and the count of consecutive 1 bits in the routing prefix (subnet mask).

Other address representations were in common use when classful networking was practiced. For example, the loopback address 127.0.0.1 was commonly written as 127.1, given that it belonged to a class-A network with eight bits for the network mask and 24 bits for the host number. When fewer than four numbers are specified in the address in dotted notation, the last value is treated as an integer of as many bytes as are required to fill out the address to four octets. Thus, the address 127.65530 is equivalent to 127.0.255.250.

Allocation

In the original design of IPv4, an IP address was divided into two parts: the network identifier was the most significant octet of the address, and the host identifier was the rest of the address. The latter was also called the rest field. This structure permitted a maximum of 256 network identifiers, which was quickly found to be inadequate.

To overcome this limit, the most-significant address octet was redefined in 1981 to create network classes, in a system which later became known as classful networking. The revised system defined five classes. Classes A, B, and C had different bit lengths for network identification. The rest of the address was used as previously to identify a host within a network. Because of the different sizes of fields in different classes, each network class had a different capacity for addressing hosts. In addition to the three classes for addressing hosts, Class D was defined for multicast addressing and Class E was reserved for future applications.

Dividing existing classful networks into subnets began in 1985 with the publication of RFC 950. This division was made more flexible with the introduction of variable-length subnet masks (VLSM) in RFC 1109 in 1987. In 1993, based on this work, RFC 1517 introduced Classless Inter-Domain Routing (CIDR), which expressed the number of bits (from the most significant) as, for instance, /24, and the class-based scheme was dubbed classful, by contrast. CIDR was designed to permit repartitioning of any address space so that smaller or larger blocks of addresses could be allocated to users. The hierarchical structure created by CIDR is managed by the Internet Assigned Numbers Authority (IANA) and the regional Internet registries (RIRs). Each RIR maintains a publicly searchable WHOIS database that provides information about IP address assignments.

Special-use addresses

The Internet Engineering Task Force (IETF) and the Internet Assigned Numbers Authority (IANA) have restricted from general use various reserved IP addresses for special purposes. Notably these addresses are used for multicast traffic and to provide addressing space for unrestricted uses on private networks.

Special address blocks

Address block	Address range	Number of addresses	Scope	Description
0.0.0.0/8	0.0.0.0–0.255.255.255	16777216	Software	Current network (only valid as source address).
10.0.0.0/8	10.0.0.0–10.255.255.255	16777216	Private network	Used for local communications within a private network.
100.64.0.0/10	100.64.0.0–100.127.255.255	4194304	Private network	Shared address space for communications between a service provider and its subscribers when using a carrier-grade NAT.
127.0.0.0/8	127.0.0.0–127.255.255.255	16777216	Host	Used for loopback addresses to the local host.
169.254.0.0/16	169.254.0.0–169.254.255.255	65536	Subnet	Used for link-local addresses between two hosts on a single link when no IP address is otherwise specified, such as would have normally been retrieved from a DHCP server.
172.16.0.0/12	172.16.0.0–172.31.255.255	1048576	Private network	Used for local communications within a private network.
192.0.0.0/24	192.0.0.0–192.0.0.255	256	Private network	IETF Protocol Assignments.
192.0.2.0/24	192.0.2.0–192.0.2.255	256	Documentation	Assigned as TEST-NET-1, documentation and examples.
192.88.99.0/24	192.88.99.0–192.88.99.255	256	Internet	Reserved. Formerly used for IPv6 to IPv4 relay (included IPv6 address block 2002::/16).
192.168.0.0/16	192.168.0.0–192.168.255.255	65536	Private network	Used for local communications within a private network.
198.18.0.0/15	198.18.0.0–198.19.255.255	131072	Private network	Used for benchmark testing of inter-network communications between two separate subnets.
198.51.100.0/24	198.51.100.0–198.51.100.255	256	Documentation	Assigned as TEST-NET-2, documentation and examples.
203.0.113.0/24	203.0.113.0–203.0.113.255	256	Documentation	Assigned as TEST-NET-3, documentation and examples.
224.0.0.0/4	224.0.0.0–239.255.255.255	268435456	Internet	In use for IP multicast. (Former Class D network).
240.0.0.0/4	240.0.0.0–255.255.255.254	268435455	Internet	Reserved for future use. (Former Class E network).
255.255.255.255/32	255.255.255.255	1	Subnet	Reserved for the "limited broadcast" destination address.

Private networks

Of the approximately four billion addresses defined in IPv4, about 18 million addresses in three ranges are reserved for use in private networks. Packets addresses in these ranges are not routable in the public Internet; they are ignored by all public routers. Therefore, private hosts cannot directly communicate with public networks, but require network address translation at a routing gateway for this purpose.

Reserved private IPv4 network ranges

Name	CIDR block	Address range	Number of addresses	Classful description
24-bit block	10.0.0.0/8	10.0.0.0 – 10.255.255.255	16777216	Single Class A.
20-bit block	172.16.0.0/12	172.16.0.0 – 172.31.255.255	1048576	Contiguous range of 16 Class B blocks.
16-bit block	192.168.0.0/16	192.168.0.0 – 192.168.255.255	65536	Contiguous range of 256 Class C blocks.

Since two private networks, e.g., two branch offices, cannot directly interoperate via the public Internet, the two networks must be bridged across the Internet via a virtual private network (VPN) or an IP tunnel, which encapsulates packets, including their headers containing the private addresses, in a protocol layer during transmission across the public network. Additionally, encapsulated packets may be encrypted for the transmission across public networks to secure the data.

Link-local addressing

RFC 3927 defines the special address block 169.254.0.0/16 for link-local addressing. These addresses are only valid on the link (such as a local network segment or point-to-point connection) directly connected to a host that uses them. These addresses are not routable. Like private addresses, these addresses cannot be the source or destination of packets traversing the internet. These addresses are primarily used for address autoconfiguration (Zeroconf) when a host cannot obtain an IP address from a DHCP server or other internal configuration methods.

When the address block was reserved, no standards existed for address autoconfiguration. Microsoft created an implementation called Automatic Private IP Addressing (APIPA), which was deployed on millions of machines and became a de facto standard. Many years later, in May 2005, the IETF defined a formal standard in RFC 3927, entitled Dynamic Configuration of IPv4 Link-Local Addresses.

Loopback

Main article: Localhost

The class A network 127.0.0.0 (classless network 127.0.0.0/8) is reserved for loopback. IP packets whose source addresses belong to this network should never appear outside a host. Packets received on a non-loopback interface with a loopback source or destination address must be dropped.

Addresses ending in 0 or 255

See also: IPv4 subnetting reference

The first address in a subnet is used to identify the subnet itself. The last address is used as a local broadcast address for all devices on the subnet.

For example, in the subnet 192.168.5.0/255.255.255.0 (192.168.5.0/24) the identifier 192.168.5.0 commonly is used to refer to the entire subnet. To avoid ambiguity in representation, the address ending in the octet 0 is reserved.

A broadcast address is an address that allows information to be sent to all interfaces in a given subnet, rather than a specific machine. The broadcast address is the last address in the address range of the subnet. For example, the broadcast address for the network 192.168.5.0 is 192.168.5.255. For networks of size /24 or larger, the broadcast address always ends in 255.

	Binary form	Dot-decimal notation
Network space	11000000.10101000.00000101.00000000	192.168.5.0
Broadcast address	11000000.10101000.00000101.11111111	192.168.5.255
In bold, is shown the host part of the IP address; the other part is the network prefix. The host gets inverted (logical NOT), but the network prefix remains intact.

However, this does not mean that every address ending in 0 or 255 cannot be used as a host address. For example, in the /16 subnet 192.168.0.0/255.255.0.0, which is equivalent to the address range 192.168.0.0–192.168.255.255, the broadcast address is 192.168.255.255. One can use the following addresses for hosts, even though they end with 255: 192.168.1.255, 192.168.2.255, etc. Also, 192.168.0.0 is the network identifier and must not be assigned to an interface. The addresses 192.168.1.0, 192.168.2.0, etc., may be assigned, despite ending with 0.

In the past, conflict between network addresses and broadcast addresses arose because some software used non-standard broadcast addresses with zeros instead of ones.

In networks smaller than /24, broadcast addresses do not necessarily end with 255. For example, a CIDR subnet 203.0.113.16/28 has the broadcast address 203.0.113.31.

	Binary form	Dot-decimal notation
Network space	11001011.00000000.01110001.00010000	203.0.113.16
Broadcast address	11001011.00000000.01110001.00011111	203.0.113.31
In bold, is shown the host part of the IP address; the other part is the network prefix. The host gets inverted (logical NOT), but the network prefix remains intact.

As a special case, a /31 network has capacity for just two hosts. These networks are typically used for point-to-point connections. There is no network identifier or broadcast address for these networks.

Address resolution

Main article: Domain Name System

Hosts on the Internet are usually known by names, e.g., www.example.com, not primarily by their IP address, which is used for routing and network interface identification. The use of domain names requires translating, called resolving, them to addresses and vice versa. This is analogous to looking up a phone number in a phone book using the recipient's name.

The translation between addresses and domain names is performed by the Domain Name System (DNS), a hierarchical, distributed naming system which allows for subdelegation of name spaces to other DNS servers.

Address space exhaustion

Main article: IPv4 address exhaustion

Since the 1980s, it was apparent that the pool of available IPv4 addresses was depleting at a rate that was not initially anticipated in the original design of the network. The main market forces that accelerated address depletion included the rapidly growing number of Internet users, who increasingly used mobile computing devices, such as laptop computers, personal digital assistants (PDAs), and smart phones with IP data services. In addition, high-speed Internet access was based on always-on devices. The threat of exhaustion motivated the introduction of a number of remedial technologies, such as Classless Inter-Domain Routing (CIDR) methods by the mid 1990s, pervasive use of network address translation (NAT) in network access provider systems, and strict usage-based allocation policies at the regional and local Internet registries.

The primary address pool of the Internet, maintained by IANA, was exhausted on 3 February 2011, when the last five blocks were allocated to the five RIRs. APNIC was the first RIR to exhaust its regional pool on 15 April 2011, except for a small amount of address space reserved for the transition technologies to IPv6, which is to be allocated under a restricted policy.

The long-term solution to the impending address exhaustion was the 1998 specification of a new version of the Internet Protocol, IPv6, which increased the address size to 128 bits. It provides a vastly increased address space, but also allows improved route aggregation across the Internet, and offers large subnetwork allocations of a minimum of 2⁶⁴ host addresses to end-users. However, IPv4 is not directly interoperable with IPv6, so that IPv4-only hosts cannot directly communicate with IPv6-only hosts. With the phase-out of the 6bone experimental network starting in 2004, permanent formal deployment of IPv6 commenced in 2006. Completion of IPv6 deployment is expected to take considerable time, so that intermediate transition technologies are necessary to permit hosts to participate in the Internet using both versions of the protocol.

Packet structure

An IP packet consists of a header section and a data section.

An IP packet has no data checksum or any other footer after the data section. Typically the link layer encapsulates IP packets in frames with a CRC footer that detects most errors, and typically the end-to-end TCP layer checksum detects most other errors.

Header

The IPv4 packet header consists of 14 fields, of which 13 are required. The 14th field is optional and aptly named: options. The fields in the header are packed with the most significant byte first (big endian), and for the diagram and discussion, the most significant bits are considered to come first (MSB 0 bit numbering). The most significant bit is numbered 0, so the version field is actually found in the four most significant bits of the first byte, for example.

IPv4 Header Format

Offsets	Octet	0								1								2								3
Octet	Bit	0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24	25	26	27	28	29	30	31
0	0	Version				IHL				DSCP						ECN		Total Length
4	32	Identification																Flags			Fragment Offset
8	64	Time To Live								Protocol								Header Checksum
12	96	Source IP Address
16	128	Destination IP Address
20	160	Options (if IHL > 5)
24	192
28	224
32	256

Version

The first header field in an IP packet is the four-bit version field. For IPv4, this is always equal to 4.

Internet Header Length (IHL)

The IPv4 header is variable in size due to the optional 14th field (options). The IHL field contains the size of the IPv4 header, it has 4 bits that specify the number of 32-bit words in the header. The minimum value for this field is 5, which indicates a length of 5 × 32 bits = 160 bits = 20 bytes. As a 4-bit field, the maximum value is 15, this means that the maximum size of the IPv4 header is 15 × 32 bits, or 480 bits = 60 bytes.

Differentiated Services Code Point (DSCP)

Originally defined as the type of service (ToS), this field specifies differentiated services (DiffServ) per RFC 2474 (updated by RFC 3168 and RFC 3260). New technologies are emerging that require real-time data streaming and therefore make use of the DSCP field. An example is Voice over IP (VoIP), which is used for interactive voice services.

Explicit Congestion Notification (ECN)

This field is defined in RFC 3168 and allows end-to-end notification of network congestion without dropping packets. ECN is an optional feature that is only used when both endpoints support it and are willing to use it. It is effective only when supported by the underlying network.

Total Length

This 16-bit field defines the entire packet size in bytes, including header and data. The minimum size is 20 bytes (header without data) and the maximum is 65,535 bytes. All hosts are required to be able to reassemble datagrams of size up to 576 bytes, but most modern hosts handle much larger packets. Sometimes links impose further restrictions on the packet size, in which case datagrams must be fragmented. Fragmentation in IPv4 is handled in either the host or in routers.

Identification

This field is an identification field and is primarily used for uniquely identifying the group of fragments of a single IP datagram. Some experimental work has suggested using the ID field for other purposes, such as for adding packet-tracing information to help trace datagrams with spoofed source addresses, but RFC 6864 now prohibits any such use.

Flags

A three-bit field follows and is used to control or identify fragments. They are (in order, from most significant to least significant):

• bit 0: Reserved; must be zero.
• bit 1: Don't Fragment (DF)
• bit 2: More Fragments (MF)

If the DF flag is set, and fragmentation is required to route the packet, then the packet is dropped. This can be used when sending packets to a host that does not have resources to handle fragmentation. It can also be used for path MTU discovery, either automatically by the host IP software, or manually using diagnostic tools such as ping or traceroute. For unfragmented packets, the MF flag is cleared. For fragmented packets, all fragments except the last have the MF flag set. The last fragment has a non-zero Fragment Offset field, differentiating it from an unfragmented packet.

Fragment Offset

The fragment offset field is measured in units of eight-byte blocks. It is 13 bits long and specifies the offset of a particular fragment relative to the beginning of the original unfragmented IP datagram. The first fragment has an offset of zero. This allows a maximum offset of (2¹³ – 1) × 8 = 65,528 bytes, which would exceed the maximum IP packet length of 65,535 bytes with the header length included (65,528 + 20 = 65,548 bytes).

Time To Live (TTL)

An eight-bit time to live field helps prevent datagrams from persisting (e.g. going in circles) on an internet. This field limits a datagram's lifetime. It is specified in seconds, but time intervals less than 1 second are rounded up to 1. In practice, the field has become a hop count—when the datagram arrives at a router, the router decrements the TTL field by one. When the TTL field hits zero, the router discards the packet and typically sends an ICMP Time Exceeded message to the sender. The program traceroute uses these ICMP Time Exceeded messages to print the routers used by packets to go from the source to the destination.

Protocol

This field defines the protocol used in the data portion of the IP datagram. The Internet Assigned Numbers Authority maintains a list of IP protocol numbers as directed by RFC 790.

Header Checksum

The 16-bit IPv4 header checksum field is used for error-checking of the header. When a packet arrives at a router, the router calculates the checksum of the header and compares it to the checksum field. If the values do not match, the router discards the packet. Errors in the data field must be handled by the encapsulated protocol. Both UDP and TCP have checksum fields.

When a packet arrives at a router, the router decreases the TTL field. Consequently, the router must calculate a new checksum.

Source address

This field is the IPv4 address of the sender of the packet. Note that this address may be changed in transit by a network address translation device.

Destination address

This field is the IPv4 address of the receiver of the packet. As with the source address, this may be changed in transit by a network address translation device.

Options

The options field is not often used. Note that the value in the IHL field must include enough extra 32-bit words to hold all the options (plus any padding needed to ensure that the header contains an integer number of 32-bit words). The list of options may be terminated with an EOL (End of Options List, 0x00) option; this is only necessary if the end of the options would not otherwise coincide with the end of the header. The possible options that can be put in the header are as follows:

Field	Size (bits)	Description
Copied	1	Set to 1 if the options need to be copied into all fragments of a fragmented packet.
Option Class	2	A general options category. 0 is for "control" options, and 2 is for "debugging and measurement". 1 and 3 are reserved.
Option Number	5	Specifies an option.
Option Length	8	Indicates the size of the entire option (including this field). This field may not exist for simple options.
Option Data	Variable	Option-specific data. This field may not exist for simple options.

• Note: If the header length is greater than 5 (i.e., it is from 6 to 15) it means that the options field is present and must be considered.
• Note: Copied, Option Class, and Option Number are sometimes referred to as a single eight-bit field, the Option Type.

Packets containing some options may be considered as dangerous by some routers and be blocked.

Data

The packet payload is not included in the checksum. Its contents are interpreted based on the value of the Protocol header field.

Some of the common payload protocols are:

Protocol Number	Protocol Name	Abbreviation
1	Internet Control Message Protocol	ICMP
2	Internet Group Management Protocol	IGMP
6	Transmission Control Protocol	TCP
17	User Datagram Protocol	UDP
41	IPv6 encapsulation	ENCAP
89	Open Shortest Path First	OSPF
132	Stream Control Transmission Protocol	SCTP

See List of IP protocol numbers for a complete list.

Fragmentation and reassembly

Main article: IP fragmentation

The Internet Protocol enables traffic between networks. The design accommodates networks of diverse physical nature; it is independent of the underlying transmission technology used in the link layer. Networks with different hardware usually vary not only in transmission speed, but also in the maximum transmission unit (MTU). When one network wants to transmit datagrams to a network with a smaller MTU, it may fragment its datagrams. In IPv4, this function was placed at the Internet Layer, and is performed in IPv4 routers, which thus require no implementation of any higher layers for the function of routing IP packets.

In contrast, IPv6, the next generation of the Internet Protocol, does not allow routers to perform fragmentation; hosts must determine the path MTU before sending datagrams.

Fragmentation

When a router receives a packet, it examines the destination address and determines the outgoing interface to use and that interface's MTU. If the packet size is bigger than the MTU, and the Do not Fragment (DF) bit in the packet's header is set to 0, then the router may fragment the packet.

The router divides the packet into fragments. The max size of each fragment is the MTU minus the IP header size (20 bytes minimum; 60 bytes maximum). The router puts each fragment into its own packet, each fragment packet having following changes:

• The total length field is the fragment size.
• The more fragments (MF) flag is set for all fragments except the last one, which is set to 0.
• The fragment offset field is set, based on the offset of the fragment in the original data payload. This is measured in units of eight-byte blocks.
• The header checksum field is recomputed.

For example, for an MTU of 1,500 bytes and a header size of 20 bytes, the fragment offsets would be multiples of ${\frac {1500-20}{8}}=185$. These multiples are 0, 185, 370, 555, 740, ...

It is possible that a packet is fragmented at one router, and that the fragments are further fragmented at another router. For example, a packet of 4,520 bytes, including the 20 bytes of the IP header (without options) is fragmented to two packets on a link with an MTU of 2,500 bytes:

Fragment	Size (bytes)	Header size (bytes)	Data size (bytes)	Flag More fragments	Fragment offset (8-byte blocks)
1	2500	20	2480	1	0
2	2040	20	2020	0	310

The total data size is preserved: 2480 bytes + 2020 bytes = 4500 bytes. The offsets are $0$ and ${\frac {0+2480}{8}}=310$.

On a link with an MTU of 1,500 bytes, each fragment results in two fragments:

Fragment	Size (bytes)	Header size (bytes)	Data size (bytes)	Flag More fragments	Fragment offset (8-byte blocks)
1	1500	20	1480	1	0
2	1020	20	1000	1	185
3	1500	20	1480	1	310
4	560	20	540	0	495

Again, the data size is preserved: 1480 + 1000 = 2480, and 1480 + 540 = 2020.

Also in this case, the More Fragments bit remains 1 for all the fragments that came with 1 in them and for the last fragment that arrives, it works as usual, that is the MF bit is set to 0 only in the last one. And of course, the Identification field continues to have the same value in all re-fragmented fragments. This way, even if fragments are re-fragmented, the receiver knows they have initially all started from the same packet.

The last offset and last data size are used to calculate the total data size: $495\times 8+540=3960+540=4500$.

Reassembly

A receiver knows that a packet is a fragment, if at least one of the following conditions is true:

• The flag "more fragments" is set, which is true for all fragments except the last.
• The field "fragment offset" is nonzero, which is true for all fragments except the first.

The receiver identifies matching fragments using the foreign and local address, the protocol ID, and the identification field. The receiver reassembles the data from fragments with the same ID using both the fragment offset and the more fragments flag. When the receiver receives the last fragment, which has the "more fragments" flag set to 0, it can calculate the size of the original data payload, by multiplying the last fragment's offset by eight, and adding the last fragment's data size. In the given example, this calculation was 495*8 + 540 = 4500 bytes.

When the receiver has all fragments, they can be reassembled in the correct sequence according to the offsets, to form the original datagram.

Assistive protocols

IP addresses are not tied in any permanent manner to hardware identifications and, indeed, a network interface can have multiple IP addresses in modern operating systems. Hosts and routers need additional mechanisms to identify the relationship between device interfaces and IP addresses, in order to properly deliver an IP packet to the destination host on a link. The Address Resolution Protocol (ARP) performs this IP-address-to-hardware-address translation for IPv4. (A hardware address is also called a MAC address.) In addition, the reverse correlation is often necessary. For example, when an IP host is booted or connected to a network it needs to determine its IP address, unless an address is preconfigured by an administrator. Protocols for such inverse correlations exist in the Internet Protocol Suite. Currently used methods are Dynamic Host Configuration Protocol (DHCP), Bootstrap Protocol (BOOTP) and, infrequently, reverse ARP.

See also

• History of the Internet
• List of assigned /8 IPv4 address blocks
• List of IP protocol numbers

External links

• Internet Assigned Numbers Authority — Internet Assigned Numbers Authority (IANA)
• IP, Internet Protocol — IP Header Breakdown, including specific options
• RFC 3344 — IPv4 Mobility
• IPv6 vs. carrier-grade NAT/squeezing more out of IPv4
• RIPE report on address consumption as of October 2003
• Official current state of IPv4 /8 allocations, as maintained by IANA
• Dynamically generated graphs of IPv4 address consumption with predictions of exhaustion dates—Geoff Huston
• IP addressing in China and the myth of address shortage
• Countdown of remaining IPv4 available addresses (estimated)