Board

How to install board-and-batten siding

• Report rights infringement
• published: 04 Nov 2015
• views: 7510

Board and batten siding installation. How to install board-and-batten siding How to install board and batten siding. Abortion bans on the upper half the shed or a combination of prime won by 10 and 0:04won by four trim boards the first step is to install some blocking in several 0:09places so that I have solid nailing for the board and batten siding with the 0:19blocking in place 0:21attack the first boorda making sure to get it wrong if it's not perfect I'll 0:25end up fighting lay out all the way across the water ok as you can see I got 0:30my first couple of boards up for the board and batten siding now the nailing 0:34pattern for this is going to be two nails in the center of the Board roughly 0:38think about dividing the board up into thirds basically the whole the edges I'm 0:42gonna come back later and install bad and should be a little water in this 0:45piece and that's going to pin down the edges of boards gonna go straight back 0:49into the flocking for now I'm using the three quarter inch spacer just to 0:53establish my course of the next board will go up to three-quarters base of the 0:57next board and so on until I get to the end of the wall 1:03ok now for the board and batten siding on the gable ends we're gonna start in 1:06the center and work our way out 1:08that's because we have a vent here so we want that to be the center of the layout 1:12now you notice that these pieces don't go all the way down to the sill they 1:16could there's no reason not to accept it makes my measurements harder than I have 1:19to worry about getting a measurement from underside of the roof down here and 1:23getting the exact by leaving a gap between the two it'll give me some 1:27wiggle room for measurements and it's all gonna be covered up by a horizontal 1:29board after anyway the board took up behind the flyer after assembly for a 1:34nice clean finished look his technique also means that the angled cut on the 1:39top of the parents doesn't have to be perfect with the board displays have to 1:44switch gears and move the trip first I'll tackle the fascia board in the back 1:48of the shed which talks up under the easiest way to handle the notches for 1:52the rafter tails is attack the board in place using Raptors area because ok now 1:59this board is gonna have to talk all the way up underneath it means I'm gonna 2:03need to have to knock it around these rafter tails but rather than trying to 2:06figure out with us layout is on the ground using a tape measure I'm just 2:10gonna take my board cut it a little bit longer than I know I need to get uptight 2:14to the bottom of the other action tales with some screws here and I'm gonna come 2:18back I'll use my speed square a pencil mark my notches out pull back down and 2:23cut of the jigsaw 2:28the windows are gonna be on our way so we really can't knock that piece of trim 2:43and slide it up don't have room to pivot into place so we're going to into pieces 2:47these pieces of five quarters from the go between the rafter tails and then a 2:52thinner piece we ripped down a slide up underneath to give the appearance of the 2:58full height of tram next comes more pre-assembled corner boards 3:08in the door and window casing which I leave long marketplace for Final Cut and 3:19then make sure to be able to bottom edges of the window casing 3:24needs the sale of the building I'm going to continue to same horizontal trip then 3:38moved to the front gable gable ends a little trickier than the other side 3:42because we have two windows and doors once we get those and then we can fill 3:48in above with the rest of the bands I just need to fill in with the pine beds 3:54the job the battens is to hide the expansion gap between the boards while 3:59also preventing them from cutting nails should go through the middle of the 4:03bands and directly into the framing the edges of the one by 10 down to prevent 4:08cups but still allowing the wide boards to expand 4:12ok all we need now on this size is the van were gonna put that in from the 4:17inside and we need to fill in the last couple of pieces of blocking that we 4:20left out with a pair of events that slide in from the inside and get fast 4:31into the frame 4:38earlier 4:43now all we hang in the opening and finish up the door where the ledge 4:53well we had two painters coming next week and then we're gonna have some 5:01landscaping and some steps foot in and #install #board #batten #siding #garden #shed #Install #Board #Batten #Siding #Garden #Shed