The most complete and in-depth video on how to build a farmhouse table. DIY PETE shows the entire process from start to finish. This farm table can be built out of everyday construction grade lumber for under $200. For more info, project photos, and downloadable plans check out: http://www.DIYPETE.com/farmhousetable Benches: http://ana-white.com/2013/10/plans/4x4-truss-benches *Note that these are affiliate links, meaning that when you buy something that is recommended below, it helps support the Channel. Thanks in advance! *Tools Needed Power Drill - http://amzn.to/1OxMfnt 12″ Miter Saw - http://amzn.to/1VUVo8s Kreg Jig - http://amzn.to/1X7Bd9H Orbital Sander - http://amzn.to/1VUVNYy Clamps - http://amzn.to/1LwiDEs *Supplies Needed 2 1/2 inch Kreg Screws - http://amzn.to/1VUVPzF 6 inch Torq Screws - Need about 40 - 4.5 inch Torq Screws - Need about 20 2.5 inch Torq Screws - Need about 20 Stain ( or White Vinegar / Steel Wool ) You’ll need to buy 4×4, 2×10, and 2×4 boards for this project. These boards can be found at your local lumber yard. Take your time to find quality boards that are straight and have little warp. First, I built the table top out of 2x10s. I used 5 2×10’s for the main part of the table and a 2×10 for each breadboard end. Ana’s plans call for four main boards, but I wanted a little larger area to spread out. I used a 12″ miter saw to make all of the cuts. I cut the 5 boards to 69 inches long. Here is a look at the table top. A 2×10 board is actually 9 1/4 inches wide. The total dimensions of the top are 46 1/4 inches by 87 1/2 inches. Set the Kreg Jig at the 1 1/2 inch setting for the stock thickness. (My video says 2 1/2 inch setting but I meant to say 1 1/2 inch.) You’ll attach each board using the 2.5 inch long Kreg Jig screws. It helps to clamp the boards to each other and use a little body weight to get the boards even with each other. Drill two pocket holes on the ends of each board as well. They will be used to connect the main boards to the breadboard. I had to modify the width of the base a bit so that it fit the wider table top. Here is a diagram of the modifications I made to Ana’s plans. I built the two ends out of 4×4’s. I used 6″ long torq screws (also known as star pattern screws or leg screws) to connect them (about 3 for each joint). The two vertical boards are cut at 10 degree angles (parallel to each other). Connect the two ends together with the 4×4 horizontal beams on top and bottom. I didn’t have an extra set up hands to help me, so I used Jack Clamps to help hold everything up while I tied the boards together with 6″ torq screws. Attach the base to the top using 4.5″ torq screws through the 4×4 beams. Use 2 inch torq screws to connect the 2×4 to the table top. (I counter sunk mine a bit). Here is a look at the completed table prior to staining and sealing the piece. I also created matching benches to fit this table. The plans can be found by clicking here. I modified the width so they are a total of 69″ wide. Instead of using a 2×10 for the breadboards I use 2×8’s. Everything else was kept the same as Ana’s plans. The inside span of my table where the benches fit in is 73″ so that left 2 inches of wiggle room on each side of the bench so it can easily slide in and out. The next step is to make the table unique to you. I decided to distress the farm table by using tools around the shop to make the table look worn. I used nails to create wormhole marks and a circular saw blade and hammer to put some character into the table. I used a #00 Steel Wool and White Vinegar solution to patina the wood and give it an aged look. Put a good handful of steel wool in a jar and add white vinegar. Let the vinegar dilute the steel wool for at least 3 to 4 days. The mixture will get darker the longer you let it sit. I let mine sit for a full week. Once diluted, simply brush the mixture on your piece. Oxidation will occur as the mixture reacts with the tannins in the wood to give it variations in color. It changed the Fir wood to dark blues, greys, browns, and black. Benches: http://ana-white.com/2013/10/plans/4x4-truss-benches ---- Looking for more DIY videos? Be sure to check out our channel and subscribe for updates! We post a weekly tutorial every Thursday. Looking for woodworking, concrete working, and other DIY projects plans to follow? You can download plans for free at http://gumroad.com/DIYPETE Facebook: http://facebook.com/DiyProjectsWithPete Instagram: http://instagram.com/diypete Pete Sveen 1627 W Main Street Suite 182 Bozeman, Montana 59715

• published: 10 Jan 2014
• views: 794898