Fuel cell

From Wikipedia, the free encyclopedia
  (Redirected from Fuel cells)
Jump to: navigation, search
For other uses, see Fuel cell (disambiguation).
Demonstration model of a direct-methanol fuel cell. The actual fuel cell stack is the layered cube shape in the center of the image
Scheme of a proton conducting fuel cell

A fuel cell is a device that converts the chemical energy from a fuel into electricity through a chemical reaction with oxygen or another oxidizing agent.[1] Hydrogen is the most common fuel, but hydrocarbons such as natural gas and alcohols like methanol are sometimes used. Fuel cells are different from batteries in that they require a constant source of fuel and oxygen/air to sustain the chemical reaction, they can however produce electricity continually for as long as these inputs are supplied.

In 1838, German Physicist Christian Friedrich Schönbein invented the first crude fuel cell.[citation needed] A year later Welsh Physicist William Grove developed his first crude fuel cells in 1839.[citation needed] The first commercial use of fuel cells was in NASA space programs to generate power for probes, satellites and space capsules. Since then, fuel cells have been used in many other applications. Fuel cells are used for primary and backup power for commercial, industrial and residential buildings and in remote or inaccessible areas. They are used to power fuel cell vehicles, including automobiles, buses, forklifts, airplanes, boats, motorcycles and submarines.

There are many types of fuel cells, but they all consist of an anode (negative side), a cathode (positive side) and an electrolyte that allows charges to move between the two sides of the fuel cell. Electrons are drawn from the anode to the cathode through an external circuit, producing direct current electricity. As the main difference among fuel cell types is the electrolyte, fuel cells are classified by the type of electrolyte they use. Fuel cells come in a variety of sizes. Individual fuel cells produce relatively small electrical potentials, about 0.7 volts, so cells are "stacked", or placed in series, to increase the voltage and meet an application's requirements.[2] In addition to electricity, fuel cells produce water, heat and, depending on the fuel source, very small amounts of nitrogen dioxide and other emissions. The energy efficiency of a fuel cell is generally between 40–60%, or up to 85% efficient if waste heat is captured for use.

The fuel cell market is also growing at a healthy pace and according to Pike Research, the stationary fuel cell market is predicted to reach 50 GW by 2020.[3]

Contents

History[edit]

Main article: Timeline of hydrogen technologies
Sketch of William Grove's 1839 fuel cell

The principle of the fuel cell was discovered by German scientist Christian Friedrich Schönbein in 1838 and published in one of the scientific magazines of the time.[4] Based on this work, the first fuel cell was demonstrated by Welsh scientist and barrister Sir William Robert Grove in the February 1839 edition of the Philosophical Magazine and Journal of Science[5] and later sketched, in 1842, in the same journal.[6] The fuel cell he made used similar materials to today's phosphoric-acid fuel cell.

In 1939, British engineer Francis Thomas Bacon successfully developed a 5 kW stationary fuel cell. In 1955, W. Thomas Grubb, a chemist working for the General Electric Company (GE), further modified the original fuel cell design by using a sulphonated polystyrene ion-exchange membrane as the electrolyte. Three years later another GE chemist, Leonard Niedrach, devised a way of depositing platinum onto the membrane, which served as catalyst for the necessary hydrogen oxidation and oxygen reduction reactions. This became known as the "Grubb-Niedrach fuel cell".[citation needed] GE went on to develop this technology with NASA and McDonnell Aircraft, leading to its use during Project Gemini. This was the first commercial use of a fuel cell. In 1959, a team led by Harry Ihrig built a 15 kW fuel cell tractor for Allis-Chalmers, which was demonstrated across the U.S. at state fairs. This system used potassium hydroxide as the electrolyte and compressed hydrogen and oxygen as the reactants. Later in 1959, Bacon and his colleagues demonstrated a practical five-kilowatt unit capable of powering a welding machine. In the 1960s, Pratt and Whitney licensed Bacon's U.S. patents for use in the U.S. space program to supply electricity and drinking water (hydrogen and oxygen being readily available from the spacecraft tanks). In 1991, the first hydrogen fuel cell automobile was developed by Roger Billings.[7]

UTC Power was the first company to manufacture and commercialize a large, stationary fuel cell system for use as a co-generation power plant in hospitals, universities and large office buildings.[8] UTC Power continues to be the sole supplier of fuel cells to NASA for use in space vehicles, having supplied fuel cells for the Apollo missions,[9] and the Space Shuttle program, and is developing fuel cells for cell phone towers and other applications.

Types of fuel cells; design[edit]

Fuel cells come in many varieties; however, they all work in the same general manner. They are made up of three adjacent segments: the anode, the electrolyte, and the cathode. Two chemical reactions occur at the interfaces of the three different segments. The net result of the two reactions is that fuel is consumed, water or carbon dioxide is created, and an electric current is created, which can be used to power electrical devices, normally referred to as the load.

At the anode a catalyst oxidizes the fuel, usually hydrogen, turning the fuel into a positively charged ion and a negatively charged electron. The electrolyte is a substance specifically designed so ions can pass through it, but the electrons cannot. The freed electrons travel through a wire creating the electric current. The ions travel through the electrolyte to the cathode. Once reaching the cathode, the ions are reunited with the electrons and the two react with a third chemical, usually oxygen, to create water or carbon dioxide.

A block diagram of a fuel cell

The most important design features in a fuel cell are[citation needed]:

  • The electrolyte substance. The electrolyte substance usually defines the type of fuel cell.
  • The fuel that is used. The most common fuel is hydrogen.
  • The anode catalyst breaks down the fuel into electrons and ions. The anode catalyst is usually made up of very fine platinum powder.The anode has a negative charge.
  • The cathode catalyst turns the ions into the waste chemicals like water or carbon dioxide. The cathode catalyst is often made up of nickel but it can also be a nanomaterial-based catalyst. The cathode has a positive charge. An easier way to remember this fact is that the cathode being pawsitive.

NOTE: that the cathode is positive and the anode negative for galvanic cells only when running in the spontaneous direction. In electrolysis, the cathode has a negative charge, and the anode has a positive charge.

A typical fuel cell produces a voltage from 0.6 V to 0.7 V at full rated load. Voltage decreases as current increases, due to several factors. Voltage is measured in volts (or joules per coulomb), while current is measured in amperes (or coulombs per unit of time):

  • Activation loss
  • Ohmic loss (voltage drop due to resistance of the cell components and interconnections)
  • Mass transport loss (depletion of reactants at catalyst sites under high loads, causing rapid loss of voltage).[10]

To deliver the desired amount of energy, the fuel cells can be combined in series and parallel circuits to yield higher voltage, and parallel-channel of configurations allow a higher current to be supplied. Such a design is called a fuel cell stack. The cell surface area can be increased, to allow stronger current from each cell. In the stack, reactant gases must be distributed uniformly over all of the cells to maximize the power output.[11][12][13]

Proton exchange membrane fuel cells[edit]

The archetypical hydrogen–oxygen proton exchange membrane fuel cell[14] (PEMFC) efficient frontier[15] design, a proton-conducting polymer membrane, (the electrolyte), separates the anode and cathode sides. This was called a "solid polymer electrolyte fuel cell" (SPEFC) in the early 1970s, before the proton exchange mechanism was well-understood. (Notice that the synonyms "polymer electrolyte membrane" and "proton exchange mechanism" result in the same acronym.)

On the anode side, hydrogen diffuses to the anode catalyst where it later dissociates into protons and electrons. These protons often react with oxidants causing them to become what is commonly referred to as multi-facilitated proton membranes. The protons are conducted through the membrane to the cathode, but the electrons are forced to travel in an external circuit (supplying power) because the membrane is electrically insulating. On the cathode catalyst, oxygen molecules react with the electrons (which have traveled through the external circuit) and protons to form water — in this example, the only waste product, either liquid or vapor.

In addition to this pure hydrogen type, there are hydrocarbon fuels for fuel cells, including diesel, methanol (see: direct-methanol fuel cells and indirect methanol fuel cells) and chemical hydrides. The waste products with these types of fuel are carbon dioxide and water.

Construction of a high temperature PEMFC: Bipolar plate as electrode with in-milled gas channel structure, fabricated from conductive composites (enhanced with graphite, carbon black, carbon fiber, and/or carbon nanotubes for more conductivity);[16] Porous carbon papers; reactive layer, usually on the polymer membrane applied; polymer membrane.
Condensation of water produced by a PEMFC on the air channel wall. The gold wire around the cell ensures the collection of electric current.[17]

The different components of a PEMFC are (i) bipolar plates, (ii) electrodes, (iii) catalyst, (iv) membrane, and (v) the necessary hardwares.[18] The materials used for different parts of the fuel cells differ by type. The bipolar plates may be made of different types of materials, such as, metal, coated metal, graphite, flexible graphite, C–C composite, carbon–polymer composites etc.[19] The membrane electrode assembly (MEA), is referred as the heart of the PEMFC and usually made of a proton exchange membrane sandwiched between two catalyst coated carbon papers. Platinum and/or similar type of noble metals are usually used as the catalyst for PEMFC. The electrolyte could be a polymer membrane.

Proton exchange membrane fuel cell design issues[edit]

  • Costs. In 2011, the Department of Energy reported that 80-kW automotive fuel cell system costs in volume production (projected to 500,000 units per year) are US$49 per kilowatt.[20] The goal is US$35 per kilowatt. Cost reduction over a ramp-up period of about 20 years is needed in order for PEM fuel cells to compete with current market technologies, including gasoline internal combustion engines.[21] Many companies are working on techniques to reduce cost in a variety of ways including reducing the amount of platinum needed in each individual cell. Ballard Power Systems has experiments with a catalyst enhanced with carbon silk, which allows a 30% reduction (1 mg/cm² to 0.7 mg/cm²) in platinum usage without reduction in performance.[22] Monash University, Melbourne uses PEDOT as a cathode.[23] A 2011 published study[24] documented the first metal-free electrocatalyst using relatively inexpensive doped carbon nanotubes, which are less than 1% the cost of platinum and are of equal or superior performance.
  • Water and air management[25] (in PEMFCs). In this type of fuel cell, the membrane must be hydrated, requiring water to be evaporated at precisely the same rate that it is produced. If water is evaporated too quickly, the membrane dries, resistance across it increases, and eventually it will crack, creating a gas "short circuit" where hydrogen and oxygen combine directly, generating heat that will damage the fuel cell. If the water is evaporated too slowly, the electrodes will flood, preventing the reactants from reaching the catalyst and stopping the reaction. Methods to manage water in cells are being developed like electroosmotic pumps focusing on flow control. Just as in a combustion engine, a steady ratio between the reactant and oxygen is necessary to keep the fuel cell operating efficiently.
  • Temperature management. The same temperature must be maintained throughout the cell in order to prevent destruction of the cell through thermal loading. This is particularly challenging as the 2H2 + O2 -> 2H2O reaction is highly exothermic, so a large quantity of heat is generated within the fuel cell.
  • Durability, service life, and special requirements for some type of cells. Stationary fuel cell applications typically require more than 40,000 hours of reliable operation at a temperature of −35 °C to 40 °C (−31 °F to 104 °F), while automotive fuel cells require a 5,000 hour lifespan (the equivalent of 240,000 km (150,000 mi)) under extreme temperatures. Current service life is 7,300 hours under cycling conditions.[26] Automotive engines must also be able to start reliably at −30 °C (−22 °F) and have a high power to volume ratio (typically 2.5 kW per liter).
  • Limited carbon monoxide tolerance of some (non-PEDOT) cathodes.

High temperature fuel cells[edit]

SOFC[edit]

Main article: Solid oxide fuel cell

Solid oxide fuel cells (SOFCs) use a solid material, most commonly a ceramic material called yttria-stabilized zirconia (YSZ), as the electrolyte. Because SOFCs are made entirely of solid materials, they are not limited to the flat plane configuration of other types of fuel cells and are often designed as rolled tubes. They require high operating temperatures (800 to 1000 °C) and can be run on a variety of fuels including natural gas.[27]

SOFCs are unique in that negatively charged oxygen ions travel from the cathode (negative side of the fuel cell) to the anode (positive side of the fuel cell) instead of positively charged hydrogen ions travelling from the anode to the cathode, as is the case in all other types of fuel cells. Oxygen gas is fed through the cathode, where it reacts with electrons to create oxygen ions. The oxygen ions then travel through the electrolyte to react with hydrogen gas at the anode. The reaction at the anode produces electricity and water as by-products. Carbon dioxide may also be a by-product depending on the fuel, but the carbon emissions from an SOFC system are less than those from a fossil fuel combustion plant.[28] The chemical reactions for the SOFC system can be expressed as follows:[29]

Anode Reaction: 2H2 + 2O2− → 2H2O + 4e−
Cathode Reaction: O2 + 4e– → 2O2−
Overall Cell Reaction: 2H2 + O2 → 2H2O

SOFC systems can run on fuels other than pure hydrogen gas. However, since hydrogen is necessary for the reactions listed above, the fuel selected must contain hydrogen atoms. For the fuel cell to operate, the fuel must be converted into pure hydrogen gas. SOFCs are capable of internally reforming light hydrocarbons such as methane (natural gas), propane and butane.[30] These fuel cells are at an early stage of development.[31]

Challenges exist in SOFC systems due to their high operating temperatures. One such challenge is the potential for carbon dust to build up on the anode, which slows down the internal reforming process. Research to address this "carbon coking" issue at the University of Pennsylvania has shown that the use of copper-based cermet (heat-resistant materials made of ceramic and metal) can reduce coking and the loss of performance.[32] Another disadvantage of SOFC systems is slow start-up time, making SOFCs less useful for mobile applications. Despite these disadvantages, a high operating temperature provides an advantage by removing the need for a precious metal catalyst like platinum, thereby reducing cost. Additionally, waste heat from SOFC systems may be captured and reused, increasing the theoretical overall efficiency to as high as 80%–85%.[27]

The high operating temperature is largely due to the physical properties of the YSZ electrolyte. As temperature decreases, so does the ionic conductivity of YSZ. Therefore, to obtain optimum performance of the fuel cell, a high operating temperature is required. According to their website, Ceres Power, a UK SOFC fuel cell manufacturer, has developed a method of reducing the operating temperature of their SOFC system to 500–600 degrees Celsius. They replaced the commonly used YSZ electrolyte with a CGO (cerium gadolinium oxide) electrolyte. The lower operating temperature allows them to use stainless steel instead of ceramic as the cell substrate, which reduces cost and start-up time of the system.[33]

MCFC[edit]

Main article: Molten carbonate fuel cell

Molten carbonate fuel cells (MCFCs) require a high operating temperature, 650 °C (1,200 °F), similar to SOFCs. MCFCs use lithium potassium carbonate salt as an electrolyte, and this salt liquefies at high temperatures, allowing for the movement of charge within the cell — in this case, negative carbonate ions.[34]

Like SOFCs, MCFCs are capable of converting fossil fuel to a hydrogen-rich gas in the anode, eliminating the need to produce hydrogen externally. The reforming process creates CO2 emissions. MCFC-compatible fuels include natural gas, biogas and gas produced from coal. The hydrogen in the gas reacts with carbonate ions from the electrolyte to produce water, carbon dioxide, electrons and small amounts of other chemicals. The electrons travel through an external circuit creating electricity and return to the cathode. There, oxygen from the air and carbon dioxide recycled from the anode react with the electrons to form carbonate ions that replenish the electrolyte, completing the circuit.[34] The chemical reactions for an MCFC system can be expressed as follows:[35]

Anode Reaction: CO32− + H2 → H2O + CO2 + 2e−
Cathode Reaction: CO2 + ½O2 + 2e− → CO32−
Overall Cell Reaction: H2 + ½O2 → H2O

As with SOFCs, MCFC disadvantages include slow start-up times because of their high operating temperature. This makes MCFC systems not suitable for mobile applications, and this technology will most likely be used for stationary fuel cell purposes. The main challenge of MCFC technology is the cells' short life span. The high temperature and carbonate electrolyte lead to corrosion of the anode and cathode. These factors accelerate the degradation of MCFC components, decreasing the durability and cell life. Researchers are addressing this problem by exploring corrosion-resistant materials for components as well as fuel cell designs that may increase cell life without decreasing performance.[27]

MCFCs hold several advantages over other fuel cell technologies, including their resistance to impurities. They are not prone to "carbon coking", which refers to carbon build-up on the anode that results in reduced performance by slowing down the internal fuel reforming process. Therefore, carbon-rich fuels like gases made from coal are compatible with the system. The Department of Energy claims that coal, itself, might even be a fuel option in the future, assuming the system can be made resistant to impurities such as sulfur and particulates that result from converting coal into hydrogen.[27] MCFCs also have relatively high efficiencies. They can reach a fuel-to-electricity efficiency of 50%, considerably higher than the 37–42% efficiency of a phosphoric acid fuel cell plant. Efficiencies can be as high as 65% when the fuel cell is paired with a turbine, and 85% if heat is captured and used in a Combined Heat and Power (CHP) system.[34]

FuelCell Energy, a Connecticut-based fuel cell manufacturer, develops and sells MCFC fuel cells. The company says that their MCFC products range from 300 kW to 2.8 MW systems that achieve 47% electrical efficiency and can utilize CHP technology to obtain higher overall efficiencies. One product, the DFC-ERG, is combined with a gas turbine and, according to the company, it achieves an electrical efficiency of 65%.[36]

Comparison of fuel cell types[edit]

Fuel cell name Electrolyte Qualified power (W) Working temperature (°C) Efficiency (cell) Efficiency (system) Status Cost (USD/W)
Metal hydride fuel cell Aqueous alkaline solution
> -20
(50% Ppeak @ 0 °C)

Commercial / Research
Electro-galvanic fuel cell Aqueous alkaline solution
< 40

Commercial / Research
Direct formic acid fuel cell (DFAFC) Polymer membrane (ionomer) < 50 W < 40

Commercial / Research
Zinc-air battery Aqueous alkaline solution
< 40
Mass production
Microbial fuel cell Polymer membrane or humic acid
< 40

Research
Upflow microbial fuel cell (UMFC)
< 40

Research
Regenerative fuel cell Polymer membrane (ionomer)
< 50

Commercial / Research
Direct borohydride fuel cell Aqueous alkaline solution
70

Commercial
Alkaline fuel cell Aqueous alkaline solution 10 – 100 kW < 80 60–70% 62% Commercial / Research
Direct methanol fuel cell Polymer membrane (ionomer) 100 mW – 1 kW 90–120 20–30% 10–20% Commercial / Research 125
Reformed methanol fuel cell Polymer membrane (ionomer) 5 W – 100 kW 250–300 (Reformer)
125–200 (PBI)		 50–60% 25–40% Commercial / Research
Direct-ethanol fuel cell Polymer membrane (ionomer) < 140 mW/cm² > 25
? 90–120

Research
Proton exchange membrane fuel cell Polymer membrane (ionomer) 100 W – 500 kW 50–120 (Nafion)
125–220 (PBI)		 50–70% 30–50% Commercial / Research 50–100
RFC - Redox Liquid electrolytes with redox shuttle and polymer membrane (Ionomer) 1 kW – 10 MW


Research
Phosphoric acid fuel cell Molten phosphoric acid (H3PO4) < 10 MW 150-200 55% 40%
Co-Gen: 90%		 Commercial / Research 4–4.50
Molten carbonate fuel cell Molten alkaline carbonate 100 MW 600–650 55% 47% Commercial / Research
Tubular solid oxide fuel cell (TSOFC) O2--conducting ceramic oxide < 100 MW 850–1100 60–65% 55–60% Commercial / Research
Protonic ceramic fuel cell H+-conducting ceramic oxide
700

Research
Direct carbon fuel cell Several different
700–850 80% 70% Commercial / Research
Planar Solid oxide fuel cell O2--conducting ceramic oxide < 100 MW 500–1100 60–65% 55–60% Commercial / Research
Enzymatic Biofuel Cells Any that will not denature the enzyme
< 40

Research
Magnesium-Air Fuel Cell Salt water
−20 to 55 90%
Commercial / Research

Efficiency of leading fuel cell types[edit]

Chart of Different Fuel Cell Types

Glossary of Terms in table:

  • Anode: The electrode at which oxidation (a loss of electrons) takes place. For fuel cells and other galvanic cells, the anode is the negative terminal; for electrolytic cells (where electrolysis occurs), the anode is the positive terminal.[37]
  • Aqueous solution: a: of, relating to, or resembling water b : made from, with, or by water.[38]
  • Catalyst: A chemical substance that increases the rate of a reaction without being consumed; after the reaction, it can potentially be recovered from the reaction mixture and is chemically unchanged. The catalyst lowers the activation energy required, allowing the reaction to proceed more quickly or at a lower temperature. In a fuel cell, the catalyst facilitates the reaction of oxygen and hydrogen. It is usually made of platinum powder very thinly coated onto carbon paper or cloth. The catalyst is rough and porous so the maximum surface area of the platinum can be exposed to the hydrogen or oxygen. The platinum-coated side of the catalyst faces the membrane in the fuel cell.[37]
  • Cathode: The electrode at which reduction (a gain of electrons) occurs. For fuel cells and other galvanic cells, the cathode is the positive terminal; for electrolytic cells (where electrolysis occurs), the cathode is the negative terminal.[37]
  • Electrolyte: A substance that conducts charged ions from one electrode to the other in a fuel cell, battery, or electrolyzer.[37]
  • Fuel Cell Stack: Individual fuel cells connected in a series. Fuel cells are stacked to increase voltage.[37]
  • Matrix: something within or from which something else originates, develops, or takes form.[39]
  • Membrane: The separating layer in a fuel cell that acts as electrolyte (an ion-exchanger) as well as a barrier film separating the gases in the anode and cathode compartments of the fuel cell.[37]
  • Molten Carbonate Fuel Cell (MCFC): A type of fuel cell that contains a molten carbonate electrolyte. Carbonate ions (CO32−) are transported from the cathode to the anode. Operating temperatures are typically near 650 °C.[37]
  • Phosphoric Acid Fuel Cell (PAFC): A type of fuel cell in which the electrolyte consists of concentrated phosphoric acid (H3PO4). Protons (H+) are transported from the anode to the cathode. The operating temperature range is generally 160–220 °C.[37]
  • Polymer Electrolyte Membrane (PEM): A fuel cell incorporating a solid polymer membrane used as its electrolyte. Protons (H+) are transported from the anode to the cathode. The operating temperature range is generally 60–100 °C.[37]
  • Solid Oxide Fuel Cell (SOFC): A type of fuel cell in which the electrolyte is a solid, nonporous metal oxide, typically zirconium oxide (ZrO2) treated with Y2O3, and O2− is transported from the cathode to the anode. Any CO in the reformate gas is oxidized to CO2 at the anode. Temperatures of operation are typically 800–1,000 °C.[37]
  • Solution: a: an act or the process by which a solid, liquid, or gaseous substance is homogeneously mixed with a liquid or sometimes a gas or solid, b : a homogeneous mixture formed by this process; especially : a single-phase liquid system, c : the condition of being dissolved[40]

For more information see Glossary of fuel cell terms

Theoretical maximum efficiency[edit]

The energy efficiency of a system or device that converts energy is measured by the ratio of the amount of useful energy put out by the system ("output energy") to the total amount of energy that is put in ("input energy") or by useful output energy as a percentage of the total input energy. In the case of fuel cells, useful output energy is measured in electrical energy produced by the system. Input energy is the energy stored in the fuel. According to the U.S. Department of Energy, fuel cells are generally between 40–60% energy efficient.[41] This is higher than some other systems for energy generation. For example, the typical internal combustion engine of a car is about 25% energy efficient.[42] In combined heat and power (CHP) systems, the heat produced by the fuel cell is captured and put to use, increasing the efficiency of the system to up to 85–90%.[27]

The theoretical maximum efficiency of any type of power generation system is rarely reached in practice, and it does not consider other steps in power generation, such as production, transportation and storage of fuel and conversion of the electricity into mechanical power. However, this calculation allows the comparison of different types of power generation. The maximum theoretical energy efficiency of a fuel cell is 83%, operating at low power density and using pure hydrogen and oxygen as reactants (assuming no heat recapture)[43] According to the World Energy Council, this compares with a maximum theoretical efficiency of 58% for internal combustion engines.[43] While these efficiencies are not approached in most real world applications, high temperature fuel cells (solid oxide fuel cells or molten carbonate fuel cells) can theoretically be combined with gas turbines to allow stationary fuel cells to come closer to the theoretical limit. A gas turbine would capture heat from the fuel cell and turn it into mechanical energy to increase the fuel cell's operational efficiency. This solution has been predicted to increase total efficiency to as much as 70%.[44]

In practice[edit]

The tank-to-wheel efficiency of a fuel cell vehicle is greater than 45% at low loads[45] and shows average values of about 36% when a driving cycle like the NEDC (New European Driving Cycle) is used as test procedure.[46] The comparable NEDC value for a Diesel vehicle is 22%. In 2008 Honda released a demonstration fuel cell electric vehicle (the Honda FCX Clarity) with fuel stack claiming a 60% tank-to-wheel efficiency.[47]

It is also important to take losses due to fuel production, transportation, and storage into account. Fuel cell vehicles running on compressed hydrogen may have a power-plant-to-wheel efficiency of 22% if the hydrogen is stored as high-pressure gas, and 17% if it is stored as liquid hydrogen.[48] Fuel cells cannot store energy like a battery,[49] except as hydrogen, but in some applications, such as stand-alone power plants based on discontinuous sources such as solar or wind power, they are combined with electrolyzers and storage systems to form an energy storage system. Most hydrogen, however, is produced by steam methane reforming, and so most hydrogen production emits carbon dioxide.[50] The overall efficiency (electricity to hydrogen and back to electricity) of such plants (known as round-trip efficiency), using pure hydrogen and pure oxygen can be "from 35 up to 50 percent", depending on gas density and other conditions.[51] While a much cheaper lead–acid battery might return about 90%, the electrolyzer/fuel cell system can store indefinite quantities of hydrogen, and is therefore better suited for long-term storage.

Solid-oxide fuel cells produce exothermic heat from the recombination of the oxygen and hydrogen. The ceramic can run as hot as 800 degrees Celsius. This heat can be captured and used to heat water in a micro combined heat and power (m-CHP) application. When the heat is captured, total efficiency can reach 80–90% at the unit, but does not consider production and distribution losses. CHP units are being developed today for the European home market.

Professor Jeremy P. Meyers, in the Electrochemical Society journal Interface in 2008, wrote, "While fuel cells are efficient relative to combustion engines, they are not as efficient as batteries, due primarily to the inefficiency of the oxygen reduction reaction (and ... the oxygen evolution reaction, should the hydrogen be formed by electrolysis of water).... [T]hey make the most sense for operation disconnected from the grid, or when fuel can be provided continuously. For applications that require frequent and relatively rapid start-ups ... where zero emissions are a requirement, as in enclosed spaces such as warehouses, and where hydrogen is considered an acceptable reactant, a [PEM fuel cell] is becoming an increasingly attractive choice [if exchanging batteries is inconvenient]".[21]

Applications[edit]

Type 212 submarine with fuel cell propulsion of the German Navy in dry dock

Power[edit]

Stationary fuel cells are used for commercial, industrial and residential primary and backup power generation. Fuel cells are very useful as power sources in remote locations, such as spacecraft, remote weather stations, large parks, communications centers, rural locations including research stations, and in certain military applications. A fuel cell system running on hydrogen can be compact and lightweight, and have no major moving parts. Because fuel cells have no moving parts and do not involve combustion, in ideal conditions they can achieve up to 99.9999% reliability.[52] This equates to less than one minute of downtime in a six-year period.[52]

Since fuel cell electrolyzer systems do not store fuel in themselves, but rather rely on external storage units, they can be successfully applied in large-scale energy storage, rural areas being one example.[53] There are many different types of stationary fuel cells so efficiencies vary, but most are between 40% and 60% energy efficient.[27] However, when the fuel cell's waste heat is used to heat a building in a cogeneration system this efficiency can increase to 85%.[27] This is significantly more efficient than traditional coal power plants, which are only about one third energy efficient.[54] Assuming production at scale, fuel cells could save 20–40% on energy costs when used in cogeneration systems.[55] Fuel cells are also much cleaner than traditional power generation; a fuel cell power plant using natural gas as a hydrogen source would create less than one ounce of pollution (other than CO2) for every 1,000 kW·h produced, compared to 25 pounds of pollutants generated by conventional combustion systems.[56] Fuel Cells also produce 97% less nitrogen oxide emissions than conventional coal-fired power plants.

Coca-Cola, Google, Walmart, Sysco, FedEx, UPS, Ikea, Staples, Whole Foods, Gills Onions, Nestle Waters, Pepperidge Farm, Sierra Nevada Brewery, Super Store Industries, Brigestone-Firestone, Nissan North America, Kimberly-Clark, Michelin and more have installed fuel cells to help meet their power needs.[57][58] One such pilot program is operating on Stuart Island in Washington State. There the Stuart Island Energy Initiative[59] has built a complete, closed-loop system: Solar panels power an electrolyzer, which makes hydrogen. The hydrogen is stored in a 500-U.S.-gallon (1,900 L) tank at 200 pounds per square inch (1,400 kPa), and runs a ReliOn fuel cell to provide full electric back-up to the off-the-grid residence. Another closed system loop was unveiled in late 2011 in Hempstead, NY.[60]

Fuel cells can be used with low-quality gas from landfills or waste-water treatment plants to generate power and lower methane emissions. A 2.8 MW fuel cell plant in California is said to be the largest of the type.[61]

Cogeneration[edit]

Combined heat and power (CHP) fuel cell systems, including Micro combined heat and power (MicroCHP) systems are used to generate both electricity and heat for homes (see home fuel cell), office building and factories. The system generates constant electric power (selling excess power back to the grid when it is not consumed), and at the same time produces hot air and water from the waste heat. MicroCHP is usually less than 5 kWe for a home fuel cell or small business.[62]

The waste heat from fuel cells can be diverted during the summer directly into the ground providing further cooling while the waste heat during winter can be pumped directly into the building. The University of Minnesota owns the patent rights to this type of system[63][64]

Co-generation systems can reach 85% efficiency (40–60% electric + remainder as thermal).[27] Phosphoric-acid fuel cells (PAFC) comprise the largest segment of existing CHP products worldwide and can provide combined efficiencies close to 90%.[65] Disadvantages are slow ramping up and down rates, high cost and short lifetime.[66][67] Molten Carbonate (MCFC) and Solid Oxide Fuel Cells (SOFC) are also used for combined heat and power generation and have electrical energy effciences around 60%.[68]

Fuel cell electric vehicles (FCEVs)[edit]

Main articles: Fuel cell vehicle, Hydrogen vehicle, and List of fuel cell vehicles
Configuration of components in a fuel cell car.
Toyota FCHV PEM FC fuel cell vehicle.
Mercedes-Benz (Daimler AG) Citaro fuel cell bus on Aldwych, London.
Toyota FCHV-BUS at the Expo 2005.
Element One fuel cell vehicle.
The world's first certified Fuel Cell Boat (HYDRA), in Leipzig/Germany

Automobiles[edit]

Although there are currently no Fuel cell vehicles available for commercial sale, over 20 FCEVs prototypes and demonstration cars have been released since 2009. Demonstration models include the Honda FCX Clarity, Toyota FCHV-adv, and Mercedes-Benz F-Cell.[69] As of June 2011 demonstration FCEVs had driven more than 4,800,000 km (3,000,000 mi), with more than 27,000 refuelings.[70] Demonstration fuel cell vehicles have been produced with "a driving range of more than 400 km (250 mi) between refueling".[71] They can be refueled in less than 5 minutes.[72] The U.S. Department of Energy's Fuel Cell Technology Program claims that, as of 2011, fuel cells achieved 53–59% efficiency at one-quarter power and 42–53% vehicle efficiency at full power,[73] and a durability of over 120,000 km (75,000 mi) with less than 10% degradation.[71] In a Well-to-Wheels simulation analysis, that "did not address the economics and market constraints", General Motors and its partners estimated that per mile traveled, a fuel cell electric vehicle running on compressed gaseous hydrogen produced from natural gas could use about 40% less energy and emit 45% less greenhouse gasses than an internal combustion vehicle.[74] A lead engineer from the Department of Energy whose team is testing fuel cell cars said in 2011 that the potential appeal is that "these are full-function vehicles with no limitations on range or refueling rate so they are a direct replacement for any vehicle. For instance, if you drive a full sized SUV and pull a boat up into the mountains, you can do that with this technology and you can't with current battery-only vehicles, which are more geared toward city driving."[75]

Some experts believe, however, that fuel cell cars will never become economically competitive with other technologies[76][77] or that it will take decades for them to become profitable.[78][79] In July 2011, the Chairman and CEO of General Motors, Daniel Akerson, stated that while the cost of hydrogen fuel cell cars is decreasing: "The car is still too expensive and probably won't be practical until the 2020-plus period, I don't know."[80]

In 2013, Lux Research, Inc. issued a report that stated: "The dream of a hydrogen economy ... is no nearer." It concluded that "Capital cost ... will limit adoption to a mere 5.9 GW" by 2030, providing "a nearly insurmountable barrier to adoption, except in niche applications". The analysis concluded that, by 2030, PEM stationary market will reach $1 billion, while the vehicle market, including forklifts, will reach a total of $2 billion.[81] Other analyses cite the lack of an extensive hydrogen infrastructure in the U.S. as an ongoing challenge to Fuel Cell Electric Vehicle commercialization. In 2006, a study for the IEEE showed that for hydrogen produced via electrolysis of water: "Only about 25% of the power generated from wind, water, or sun is converted to practical use." The study further noted that "Electricity obtained from hydrogen fuel cells appears to be four times as expensive as electricity drawn from the electrical transmission grid. ... Because of the high energy losses [hydrogen] cannot compete with electricity."[82] Furthermore, the study found: "Natural gas reforming is not a sustainable solution".[82] "The large amount of energy required to isolate hydrogen from natural compounds (water, natural gas, biomass), package the light gas by compression or liquefaction, transfer the energy carrier to the user, plus the energy lost when it is converted to useful electricity with fuel cells, leaves around 25% for practical use."[21][45][83] Despite this, several major car manufacturers have announced plans to introduce a production model of a fuel cell car in 2015. Toyota has stated that it plans to introduce such a vehicle at a price of around US$50,000.[84] Mercedes-Benz announced that they would move the scheduled production date of their fuel cell car from 2015 up to 2014, asserting that "The product is ready for the market technically. ... The issue is infrastructure."[85] At the Paris Auto Show in September 2012, Hyundai announced that it plans to begin producing a commercial production fuel cell model (based on the ix35) in December 2012 and hopes to deliver 1,000 of them by 2015.[86] Other manufacturers planning to sell fuel cell electric vehicles commercially by 2016 or earlier include General Motors (2015),[87] Honda (2015 in Japan),[88] and Nissan (2016).[89]

The Obama Administration sought to reduce funding for the development of fuel cell vehicles, concluding that other vehicle technologies will lead to quicker reduction in emissions in a shorter time.[90] Steven Chu, the United States Secretary of Energy, stated in 2009 that hydrogen vehicles "will not be practical over the next 10 to 20 years".[91][92] In 2012, however, Chu stated that he saw fuel cell cars as more economically feasible as natural gas prices have fallen and hydrogen reforming technologies have improved.[93][94]

Buses[edit]

In total there are over 100 fuel cell buses deployed around the world today. Most buses are produced by UTC Power, Toyota, Ballard, Hydrogenics, and Proton Motor. UTC Buses have already accumulated over 970,000 km (600,000 mi) of driving.[95] Fuel cell buses have a 39–141% higher fuel economy than diesel buses and natural gas buses.[96] Fuel cell buses have been deployed around the world including in Whistler, Canada; San Francisco, United States; Hamburg, Germany; Shanghai, China; London, England; São Paulo, Brazil; as well as several others.[97] The Fuel Cell Bus Club is a global cooperative effort in trial fuel cell buses. Notable Projects Include:

  • 12 Fuel cell buses are being deployed in the Oakland and San Francisco Bay area of California.[97]
  • Daimler AG, with thirty-six experimental buses powered by Ballard Power Systems fuel cells completed a successful three-year trial, in eleven cities, in January 2007.[98][99]
  • A fleet of Thor buses with UTC Power fuel cells was deployed in California, operated by SunLine Transit Agency.[100]

The first Brazilian hydrogen fuel cell bus prototype in Brazil was deployed in São Paulo. The bus was manufactured in Caxias do Sul and the hydrogen fuel will be produced in São Bernardo do Campo from water through electrolysis. The program, called "Ônibus Brasileiro a Hidrogênio" (Brazilian Hydrogen Autobus), includes three additional buses.[101][102]

Forklifts[edit]

Fuel cell powered forklifts are one of the largest sectors of fuel cell applications in the industry.[103] Most fuel cells used for material handling purposes are powered by PEM fuel cells, although some direct methanol fuel forklifts are coming onto the market. Fuel cell fleets are currently being operated by a large number of companies, including Sysco Foods, FedEx Freight, GENCO (at Wegmans, Coca-Cola, Kimberly Clark, and Whole Foods), and H-E-B Grocers.[104]

Fuel cell powered forklifts provide significant benefits over both petroleum and battery powered forklifts as they produce no local emissions, can work for a full 8 hour shift on a single tank of hydrogen, can be refueled in 3 minutes and have a lifetime of 8–10 years. Fuel cell powered forklifts are often used in refrigerated warehouses as their performance is not degraded by lower temperatures. Many companies do not use petroleum powered forklifts, as these vehicles work indoors where emissions must be controlled and instead are turning towards electric forklifts. Fuel cell forklifts offer green house gas, product lifetime, maintenance cost, refueling and labor cost benefits over battery operated fork lifts.[105]

Motorcycles and bicycles[edit]

In 2005 the British firm Intelligent Energy produced the first ever working hydrogen run motorcycle called the ENV (Emission Neutral Vehicle). The motorcycle holds enough fuel to run for four hours, and to travel 160 km (100 mi) in an urban area, at a top speed of 80 km/h (50 mph).[106] In 2004 Honda developed a fuel-cell motorcycle that utilized the Honda FC Stack.[107][108] There are other examples of bikes[109] and bicycles[110] with a hydrogen fuel cell engine. The Taiwanese company APFCT conducts a live street test with 80 fuel cell scooters[111] for Taiwans Bureau of Energy using the fueling system from Italy's Acta SpA[citation needed] with a 2012 production target of 1,000 fuel cell scooters. De Burgman received "whole vehicle type" approval in the EU.[112]

Airplanes[edit]

Boeing researchers and industry partners throughout Europe conducted experimental flight tests in February 2008 of a manned airplane powered only by a fuel cell and lightweight batteries. The Fuel Cell Demonstrator Airplane, as it was called, used a Proton Exchange Membrane (PEM) fuel cell/lithium-ion battery hybrid system to power an electric motor, which was coupled to a conventional propeller.[113] In 2003, the world's first propeller-driven airplane to be powered entirely by a fuel cell was flown. The fuel cell was a unique FlatStackTM stack design, which allowed the fuel cell to be integrated with the aerodynamic surfaces of the plane.[114]

There have been several fuel cell powered unmanned aerial vehicles (UAV). A Horizen fuel cell UAV set the record distance flow for a small UAV in 2007.[115] The military is especially interested in this application because of the low noise, low thermal signature and ability to attain high altitude. In 2009 the Naval Research Laboratory's (NRL's) Ion Tiger utilized a hydrogen-powered fuel cell and flew for 23 hours and 17 minutes.[116] Fuel cells are also being used to provide auxiliary power in aircraft, replacing fossil fuel generators that were previously used to start the engines and power on board electrical needs.[117][not in citation given] Fuel cells can help airplanes reduce CO2 and other pollutant emissions and noise.

Boats[edit]

The world's first Fuel Cell Boat HYDRA used an AFC system with 6.5 kW net output. Iceland has committed to converting its vast fishing fleet to use fuel cells to provide auxiliary power by 2015 and, eventually, to provide primary power in its boats. Amsterdam recently introduced its first fuel cell powered boat that ferries people around the city's famous and beautiful canals.[118]

Submarines[edit]

The Type 212 submarines of the German and Italian navies use fuel cells to remain submerged for weeks without the need to surface.

The U212A is a non-nuclear submarine developed by German naval shipyard Howaldtswerke Deutsche Werft.[119] The system consists of nine PEM fuel cells, providing between 30 kW and 50 kW each. The ship is silent giving it an advantage in the detection of other submarines.[120]

Other applications[edit]

Fueling stations[edit]

Main articles: Hydrogen station and Hydrogen highway
Hydrogen fueling station.

There were over 85 hydrogen refueling stations in the U.S. in 2010.[127]

As of June 2012 California had 23 hydrogen refueling stations in operation.[127][128] Honda announced plans in March 2011 to open the first station that would generate hydrogen through solar-powered renewable electrolysis.[citation needed] South Carolina also has two hydrogen fueling stations, in Aiken and Columbia, SC. The University of South Carolina, a founding member of the South Carolina Hydrogen & Fuel Cell Alliance, received 12.5 million dollars from the United States Department of Energy for its Future Fuels Program.[129]

The first public hydrogen refueling station in Iceland was opened in Reykjavík in 2003. This station serves three buses built by DaimlerChrysler that are in service in the public transport net of Reykjavík. The station produces the hydrogen it needs by itself, with an electrolyzing unit (produced by Norsk Hydro), and does not need refilling: all that enters is electricity and water. Royal Dutch Shell is also a partner in the project. The station has no roof, in order to allow any leaked hydrogen to escape to the atmosphere.[citation needed]

The current 14 stations nationwide in Germany are planned to be expanded to 50 by 2015[130] through its public private partnership Now GMBH.[131] Japan also has a hydrogen highway, as part of the Japan hydrogen fuel cell project. Twelve hydrogen fueling stations have been built in 11 cities in Japan and another 100 hydrogen stations are expected to be operational by 2015.[132] Canada, Sweden and Norway also have hydrogen highways being implemented.[citation needed]

Markets and economics[edit]

Main article: Hydrogen economy

In 2010, fuel cell industry revenues exceeded a $750 million market value worldwide,[133] although, as of 2010, no public company in the industry had yet become profitable.[134] There were 140,000 fuel cell stacks shipped globally in 2010, up from 11 thousand shipments in 2007, and in 2010 worldwide fuel cell shipments had an annual growth rate of 115%.[135] Approximately 50% of fuel cell shipments in 2010 were stationary fuel cells, up from about a third in 2009, and the four dominant producers in the Fuel Cell Industry remain the United States, Germany, Japan and South Korea.[136] The Department of Energy Solid State Energy Conversion Alliance found that, as of January 2011, stationary fuel cells generated power at approximately $724 to $775 per kilowatt installed.[137] Bloom Energy, a major fuel cell supplier, says its fuel cells will meet a return on investment in 3–5 years, as its fuel cells generate power at 9–11 cents per kilowatt-hour, including the price of fuel, maintenance, and hardware.[138][139]

Low temperature fuel cell stacks proton exchange membrane fuel cell (PEMFC), direct methanol fuel cell (DMFC) and phosphoric acid fuel cell (PAFC) use a platinum catalyst. Impurities create catalyst poisoning (reducing activity and efficiency) in these low-temperature fuel cells, thus high hydrogen purity or higher catalyst densities are required.[140] Although there are sufficient platinum resources for future demand,[141] most predictions of platinum running out and/or platinum prices soaring do not take into account effects of reduction in catalyst loading and recycling. Recent research at Brookhaven National Laboratory could lead to the replacement of platinum by a gold-palladium coating, which may be less susceptible to poisoning and thereby improve fuel cell lifetime considerably.[142] Another method would use iron and sulphur instead of platinum. This is possible through an intermediate conversion by bacteria. This would lower the cost of a fuel cell substantially (as the platinum in a regular fuel cell costs around US$1,500, and the same amount of iron costs only around US$1.50). The concept is being developed by a coalition of the John Innes Centre and the University of Milan-Bicocca.[143] PEDOT cathodes are immune to monoxide poisoning.[144]

Current targets for a transport PEM fuel cells are 0.2 g/kW Pt – which is a factor of 5 decrease over current loadings – and recent comments from major original equipment manufacturers (OEMs) indicate that this is possible. Recycling of fuel cells components, including platinum, will conserve supplies. High-temperature fuel cells, including molten carbonate fuel cells (MCFC's) and solid oxide fuel cells (SOFC's), do not use platinum as catalysts, but instead use cheaper materials such as nickel and nickel oxide. They also do not experience catalyst poisoning by carbon monoxide, and so they do not require high-purity hydrogen to operate. They can use fuels with an existing and extensive infrastructure, such as natural gas, directly, without having to first reform it externally to hydrogen and CO followed by CO removal.

Research and development[edit]

See also[edit]

Portal icon Electronics portal
Portal icon Energy portal
Portal icon Sustainable development portal

References[edit]

  1. ^ Khurmi, R. S. Material Science. 
  2. ^ Nice, Karim and Strickland, Jonathan. "How Fuel Cells Work: Polymer Exchange Membrane Fuel Cells". How Stuff Works, accessed August 4, 2011
  3. ^ Prabhu, Rahul R. (2013-01-13). "Stationary Fuel Cells Market size to reach 350,000 Shipments by 2022". Renew India Campaign. Retrieved 2013-01-14. 
  4. ^ George Wand. "Fuel Cells History, part 1". Johnson Matthey plc. Retrieved 2012-09-23. "In January 1839 the German/Swiss chemist Christian Friedrich Schönbein wrote an article in one of the scientific magazines of the time about his discovery of ozone and about the reaction of hydrogen and oxygen. But it was no other than William Grove to document just one month later, in February of 1839, his observations in the "Philosophical Magazine". He had conducted a series of experiments with his second invention, which he termed a gas voltaic battery." 
  5. ^ Grove, William Robert "On Voltaic Series and the Combination of Gases by Platinum", Philosophical Magazine and Journal of Science vol. XIV (1839), pp. 127–130.
  6. ^ Grove, William Robert "On a Gaseous Voltaic Battery", Philosophical Magazine and Journal of Science vol. XXI (1842), pp. 417–420.
  7. ^ "Roger Billings Biography". International Association for Hydrogen Energy. Retrieved 2011-03-08. 
  8. ^ "The PureCell Model 400 - Product Overview". UTC Power. Retrieved 2011-12-22. 
  9. ^ "Apollo Space Program Hydrogen Fuel Cells". Spaceaholic.com. Retrieved 2009-09-21. 
  10. ^ Larminie, James (1 May 2003). Fuel Cell Systems Explained, Second Edition. SAE International. ISBN 0-7680-1259-7. 
  11. ^ Wang, J.Y. (2008). "Pressure drop and flow distribution in parallel-channel of configurations of fuel cell stacks: U-type arrangement". Int. J. of Hydrogen Energy 33 (21): 6339–6350. doi:10.1016/j.ijhydene.2008.08.020. 
  12. ^ Wang, J.Y.; Wang, H.L. (2012). Flow field designs of bipolar plates in PEM fuel cells: theory and applications, Fuel Cells, 12 (6). pp. 989–1003. doi:10.1002/fuce.201200074. 
  13. ^ Wang, J.Y.; Wang, H.L. (2012). "Discrete approach for flow-field designs of parallel channel configurations in fuel cells". Int. J. of Hydrogen Energy 37 (14): 10881–10897. doi:10.1016/j.ijhydene.2012.04.034. 
  14. ^ Anne-Claire Dupuis, Progress in Materials Science, Volume 56, Issue 3, March 2011, pp. 289–327
  15. ^ Measuring the relative efficiency of hydrogen energy technologies for implementing the hydrogen economy 2010
  16. ^ Kakati, B. K., Deka, D., "Effect of resin matrix precursor on the properties of graphite composite bipolar plate for PEM fuel cell", Energy & Fuels 2007, 21 (3):1681–1687.
  17. ^ "LEMTA - Our fuel cells". Perso.ensem.inpl-nancy.fr. Retrieved 2009-09-21. 
  18. ^ Kakati B. K., Mohan V., "Development of low cost advanced composite bipolar plate for P.E.M. fuel cell", Fuel Cells 2008, 08(1): 45–51
  19. ^ Kakati B. K., Deka D., "Differences in physico-mechanical behaviors of resol and novolac type phenolic resin based composite bipolar plate for proton exchange membrane (PEM) fuel cell", Electrochimica Acta 2007, 52 (25): 7330–7336.
  20. ^ Fuel cell system cost
  21. ^ a b c Meyers, Jeremy P. "Getting Back Into Gear: Fuel Cell Development After the Hype". The Electrochemical Society Interface, Winter 2008, pp. 36–39, accessed August 7, 2011
  22. ^ "Ballard Power Systems: Commercially Viable Fuel Cell Stack Technology Ready by 2010". 2005-03-29. Archived from the original on September 27, 2007. Retrieved 2007-05-27. 
  23. ^ a b Online, Science (2008-08-02). "2008 - Cathodes in fuel cells". Abc.net.au. Retrieved 2009-09-21. 
  24. ^ http://pubs.acs.org/doi/abs/10.1021/ja1112904?journalCode=jacsat
  25. ^ "Water_and_Air_Management". Ika.rwth-aachen.de. Retrieved 2009-09-21. 
  26. ^ "Fuel Cell School Buses: Report to Congress" (PDF). Retrieved 2009-09-21. 
  27. ^ a b c d e f g h "Types of Fuel Cells". Department of Energy EERE website, accessed August 4, 2011
  28. ^ Stambouli, A. Boudghene. "Solid oxide fuel cells (SOFCs): a review of an environmentally clean and efficient source of energy". Renewable and Sustainable Energy Reviews, Vol. 6, Issue 5, pp. 433–455, October 2002.
  29. ^ "Solid Oxide Fuel Cell (SOFC)". FCTec website', accessed August 4, 2011
  30. ^ A Kulkarni, FT Ciacchi, S Giddey, C Munnings, SPS Badwal, JA Kimpton, D Fini (2012). "International Journal of Hydrogen Energy". International Journal of Hydrogen Energy 37 (24): 19092–19102. doi:10.1016/j.ijhydene.2012.09.141. 
  31. ^ S. Giddey, S.P.S. Badwal, A. Kulkarni, C. Munnings (2012). "A comprehensive review of direct carbon fuel cell technology". Progress in Energy and Combustion Science 38 (3): 360–399. doi:10.1016/j.pecs.2012.01.003. 
  32. ^ Hill, Michael. "Ceramic Energy: Material Trends in SOFC Systems". Ceramic Industry, September 1, 2005.
  33. ^ "The Ceres Cell". Ceres Power website, accessed August 4, 2011
  34. ^ a b c "Molten Carbonate Fuel Cell Technology". U.S. Department of Energy, accessed August 9, 2011
  35. ^ "Molten Carbonate Fuel Cells (MCFC)". FCTec.com, accessed August 9, 2011
  36. ^ "Products". FuelCell Energy, accessed August 9, 2011
  37. ^ a b c d e f g h i j "Fuel Cell Technologies Program: Glossary". Department of Energy Energy Efficiency and Renewable Energy Fuel Cell Technologies Program. 07/07/2011. Accessed August 3rd 2011.
  38. ^ "Aqueous Solution". Merriam-Webster Free Online Dictionary
  39. ^ "Matrix". Merriam-Webster Free Online Dictionary
  40. ^ "Solution". Merriam-Webster Free Online Dictionary
  41. ^ "Comparison of Fuel Cell Technologies". U.S. Department of Energy, Energy Efficiency and Fuel Cell Technologies Program, February 2011, accessed August 4, 2011
  42. ^ "Fuel Economy: Where The Energy Goes". U.S. Department of Energy, Energy Effciency and Renewable Energy, accessed August 3, 2011
  43. ^ a b "Fuel Cell Efficiency". World Energy Council, July 17, 2007, accessed August 4, 2011
  44. ^ Milewski, J., A. Miller and K. Badyda. "The Control Strategy for High Temperature Fuel Cell Hybrid Systems". The Online Journal on Electronics and Electrical Engineering, Vol. 2, No. 4, p. 331, 2009, accessed August 4, 2011
  45. ^ a b Eberle, Ulrich and Rittmar von Helmolt. "Sustainable transportation based on electric vehicle concepts: a brief overview". Energy & Environmental Science, Royal Society of Chemistry, May 14, 2010, accessed August 2, 2011
  46. ^ Von Helmolt, R.; Eberle, U (2007-03-20). "Fuel Cell Vehicles:Status 2007". Journal of Power Sources 165 (2): 833. doi:10.1016/j.jpowsour.2006.12.073. 
  47. ^ "Honda FCX Clarity - Fuel cell comparison". Honda. Retrieved 2009-01-02. 
  48. ^ "Efficiency of Hydrogen PEFC, Diesel-SOFC-Hybrid and Battery Electric Vehicles" (PDF). 2003-07-15. Retrieved 2007-05-23. 
  49. ^ "Batteries, Supercapacitors, and Fuel Cells: Scope". Science Reference Services. 20 August 2007. Retrieved 11 February 2009. 
  50. ^ Nice, Karim. "How Fuel Processors Work". HowStuffWorks, accessed August 3, 2011
  51. ^ Garcia, Christopher P. et al. (January 2006). Round Trip Energy Efficiency of NASA Glenn Regenerative Fuel Cell System. Preprint. p. 5. Retrieved August 4, 2011. 
  52. ^ a b "Fuel Cell Basics: Benefits". Fuel Cells 2000. Retrieved 2007-05-27. 
  53. ^ "Fuel Cell Basics: Applications". Fuel Cells 2000. Accessed August 2, 2011.
  54. ^ "Energy Sources: Electric Power". U.S. Department of Energy. Accessed August 2, 2011.
  55. ^ "2008 Fuel Cell Technologies Market Report". Bill Vincent of the Breakthrough Technologies Institute, Jennifer Gangi, Sandra Curtin, and Elizabeth Delmont. Department of Energy Energy Efficiency and Renewable Energy. June 2010.
  56. ^ U.S. Fuel Cell Council Industry Overview 2010, p. 12. U.S. Fuel Cell Council. 2010.
  57. ^ Kuo, Iris. "Coca-Cola, Walmart sign up for Bloom's new fuel-cell electricity service". venturebeat.com. Retrieved 13 January 2012. 
  58. ^ "The Business Case For Fuel Cells: Why Top Companies are Purchasing Fuel Cells Today". Sandra Curtin and Jennifer Gangi. Fuel Cells 2000. September 2010.
  59. ^ "Stuart Island Energy Initiative". Siei.org. Retrieved 2009-09-21.  - gives extensive technical details
  60. ^ "Town's Answer to Clean Energy is Blowin' in the Wind: New Wind Turbine Powers Hydrogen Car Fuel Station". Town of Hempstead. Retrieved 13 January 2012. 
  61. ^ World's Largest Carbon Neutral Fuel Cell Power Plant, October 16, 2012
  62. ^ COGEN EUROPE
  63. ^ "Patent 7,334,406". Retrieved 25 August 2011. 
  64. ^ "Geothermal Heat, Hybrid Energy Storage System". Retrieved 25 August 2011. 
  65. ^ "PureCell Model 400: Overview". UTC Power. Accessed August 2, 2011.
  66. ^ H.I. Onovwiona and V.I. Ugursal. Residential cogeneration systems: review of the current technology. Renewable and Sustainable Energy Reviews, 10(5):389 – 431, 2006.
  67. ^ AD. Hawkes, L. Exarchakos, D. Hart, MA. Leach, D. Haeseldonckx, L. Cosijns and W. D’haeseleer. EUSUSTEL work package 3: Fuell cells, 2006.
  68. ^ "Comparison of Fuel Cell Technologies". Departement of Energy Energy Efficiency and Renewable Energy Fuel Cell Technologies Program. February 2011.
  69. ^ "Hydrogen and Fuel Cell Vehicles Worldwide". TÜV SÜD Industrie Service GmbH, accessed on August 2, 2011
  70. ^ Wipke, Keith, Sam Sprik, Jennifer Kurtz and Todd Ramsden. "Controlled Hydrogen Fleet and Infrastructure Demonstration and Validation Project". National Renewable Energy Laboratory, September 11, 2009, accessed on August 2, 2011
  71. ^ a b "Accomplishments and Progress". Fuel Cell Technology Program, U.S. Dept. of Energy, June 24, 2011
  72. ^ Wipke, Keith, Sam Sprik, Jennifer Kurtz and Todd Ramsden. "National FCEV Learning Demonstration". National Renewable Energy Laboratory, April 2011, accessed August 2, 2011
  73. ^ Garbak, John. "VIII.0 Technology Validation Sub-Program Overview". DOE Fuel Cell Technologies Program, FY 2010 Annual Progress Report, accessed August 2, 2011
  74. ^ Brinkman, Norma, Michael Wang, Trudy Weber and Thomas Darlington. "Well-To-Wheels Analysis of Advanced Fuel/Vehicle Systems – A North American Study of Energy Use, Greenhouse Gas Emissions, and Criteria Pollutant Emissions". General Motors Corporation, Argonne National Laboratory and Air Improvement Resource, Inc., May 2005, accessed August 9, 2011
  75. ^ Lammers, Heather (2011-08-17). "Low Emission Cars Under NREL's Microscope". NREL Newsroom. Retrieved 2011-08-21. 
  76. ^ "From TechnologyReview.com "Hell and Hydrogen", March 2007". Technologyreview.com. Retrieved 2011-01-31. 
  77. ^ White, Charlie. "Hydrogen fuel cell vehicles are a fraud" Dvice TV, July 31, 2008
  78. ^ Squatriglia, Chuck. "Hydrogen Cars Won't Make a Difference for 40 Years", Wired, May 12, 2008
  79. ^ Boyd, Robert S. "Hydrogen cars may be a long time coming". McClatchy Newspapers, May 15, 2007, accessed August 13, 2011
  80. ^ "GM CEO: Fuel cell vehicles not yet practical", The Detroit News, July 30, 2011; and Chin, Chris. "GM's Dan Akerson: Fuel-cell vehicles aren't practical… yet". egmCarTech, August 1, 2011, accessed February 27, 2012
  81. ^ Brian Warshay, Brian. "The Great Compression: the Future of the Hydrogen Economy", Lux Research, Inc. January 2013
  82. ^ a b Bossel, Ulf. "Does a Hydrogen Economy Make Sense? Proceedings of the IEEE Vol. 94, No. 10, October 2006.
  83. ^ Zyga, Lisa. "Why a hydrogen economy doesn't make sense". physorg.com, December 11, 2006, accessed August 2, 2011, citing Bossel, Ulf. "Does a Hydrogen Economy Make Sense?" Proceedings of the IEEE. Vol. 94, No. 10, October 2006
  84. ^ Squatriglia, Chuck. "Hydrogen Is Down, But Not Out". Wired.com, Autopia, March 17, 2011, accessed on August 2, 2011
  85. ^ Lienert, Anita. "Mercedes-Benz Fuel-Cell Car Ready for Market in 2014". Edmunds Inside Line, June 21, 2011
  86. ^ Korzeniewski, Jeremy (2012-09-27). "Hyundai ix35 lays claim to world's first production fuel cell vehicle title". autoblog.com. Retrieved 2012-10-07. 
  87. ^ "GM's Fuel Cell System Shrinks in Size, Weight, Cost". General Motors. March 16, 2010. Retrieved 5 March 2012. 
  88. ^ "Honda unveils FCX Clarity advanced fuel cell electric vehicle at motor show in US". Honda Worldwide. Retrieved 5 March 2012. 
  89. ^ "Environmental Activities: Nissan Green Program 2016". Nissan. Retrieved 5 March 2012. 
  90. ^ Chu, Steven. "Winning the Future with a Responsible Budget". U.S. Dept. of Energy, February 11, 2011
  91. ^ Matthew L. Wald (2009-05-07). "U.S. Drops Research Into Fuel Cells for Cars". The New York Times. Retrieved 2009-05-09. 
  92. ^ Bullis, Kevin. "Q & A: Steven Chu", Technology Review, May 14, 2009
  93. ^ Steven Chu turns out to be a supporter of Hydrogen Technologies - on 2.10 min
  94. ^ Motavalli, Jim. "Cheap Natural Gas Prompts Energy Department to Soften Its Line on Fuel Cells", The New York Times, 29 May 2012
  95. ^ "Transportation Fleet Vehicles: Overview". UTC Power. Accessed August 2, 2011.
  96. ^ "FY 2010 annual progress report: VIII.0 Technology Validation Sub-Program Overview".John Garbak. Department of Energy Hydrogen Program.
  97. ^ a b "National Fuel Cell Bus Program Awards". Calstart. Accessed 12 August 2011
  98. ^ "European Fuel Cell Bus Project Extended by One Year". DaimlerChrysler. Retrieved 2007-03-31. [dead link]
  99. ^ "Fuel cell buses". Transport for London. Archived from the original on May 13, 2007. Retrieved 2007-04-01. 
  100. ^ "UTC Power - Fuel Cell Fleet Vehicles". [dead link]
  101. ^ "Ônibus brasileiro movido a hidrogênio começa a rodar em São Paulo" (in Portuguese). Inovação Tecnológica. 2009-04-08. Retrieved 2009-05-03. 
  102. ^ "Ônibus a Hidrogênio vira realidade no Brasil" (in Portuguese). Inovação Tecnológica. Abril 2009. Retrieved 2009-05-03. [dead link]
  103. ^ "Hydrogen Fueling Stations Could Reach 5,200 by 2020". Environmental Leader: Environmental & Energy Management News,July 20, 2011, accessed August 2, 2011
  104. ^ "Fact Sheet: Materials Handling and Fuel Cells". Fuel Cell and Hydrogen Energy Association. Accessed August 2, 2011.
  105. ^ "Early Markets: Fuel Cells for Material Handling Equipment". U.S. Department of Energy Fuel Cell Technologies Program, February 2011, accessed August 2, 2011
  106. ^ "The ENV Bike". Intelligent Energy. Retrieved 2007-05-27. 
  107. ^ "Honda Develops Fuel Cell Scooter Equipped with Honda FC Stack". Honda Motor Co. 2004-08-24. Retrieved 2007-05-27. 
  108. ^ Bryant, Eric (2005-07-21). "Honda to offer fuel-cell motorcycle". autoblog.com. Retrieved 2007-05-27. 
  109. ^ 15. Dezember 2007. "Hydrogen Fuel Cell electric bike". Youtube.com. Retrieved 2009-09-21. 
  110. ^ "Horizon fuel cell vehicles: Transportation: Light Mobility". Horizon Fuel Cell Technologies. 2010. Accessed August 2, 2011.
  111. ^ APFCT won Taiwan BOE project contract for 80 FC scooters fleet demonstration
  112. ^ Burgman_Fuel-Cell_Scooter
  113. ^ "Boeing Successfully Flies Fuel Cell-Powered Airplane". . Boeing. April 3, 2008. Accessed August 2, 2011.
  114. ^ "First Fuel Cell Microaircraft"[dead link]
  115. ^ "Horizon Fuel Cell Powers New World Record in UAV Flight". Horizon Fuel Cell Technologies. November 1, 2007.
  116. ^ "Fuel Cell Powered UAV Completes 23-hour Flight". Alternative Energy: News. October 22, 2009. Accessed August 2, 2011.
  117. ^ "Hydrogen-powered unmanned aircraft completes set of tests".www.theengineer.co.uk. 20 June 2011. Accessed August 2, 2011.
  118. ^ "Lovers introduces zero-emission boat" (in Dutch). NemoH2. March 28th 2011. Accessed August 2, 2011.
  119. ^ "Super-stealth sub powered by fuel cell". Frederik Pleitgen. CNN Tech: Nuclear Weapons. February 22, 2011. Accessed August 2, 2011.
  120. ^ "U212 / U214 Attack Submarines, Germany". Navel-Technology.com. Accessed August 2, 2011.
  121. ^ "Ballard fuel cells to power telecom backup power units for motorola". Association Canadienne de l'hydrogene et des piles a combustible. July 13th 2009. Accessed August 2, 2011.
  122. ^ India telecoms to get fuel cell power[dead link]
  123. ^ "Cottbus receives new local data center". T Systems. March 21, 2011.
  124. ^ "Fuel Cell Applications". Fuel Cells 2000. Accessed August 2, 2011
  125. ^ DVGW VP 119 Brennstoffzellen-Gasgeräte bis 70 kW. DVGW. (German)
  126. ^ Laine Welch (May 18, 2013). "Laine Welch: Fuel cell technology boosts long-distance fish shipping". Anchorage Daily News. Retrieved May 19, 2013. 
  127. ^ a b "Alternative Fueling Station Locator". U.S. Department of Energy Energy Efficiency and Renewable Energy Alternative Fuel & Advance Vehicle Center. 01/14/2010.
  128. ^ Ingram, Antony. "RIP Hydrogen Highway? California Takes Back Grant Dollars", Green Car Reports, June 5, 2012
  129. ^ "Cluster Successes in South Carolina". South Carolina Hydrogen & Fuel Cell Alliance. 200
  130. ^ German Government announces support for 50 urban hydrogen refuelling stations
  131. ^ Bundesverkehrsministerium und Industriepartner bauen überregionales Tankstellennetz (German)
  132. ^ Initiative to Promote a Diffusion of Hydrogen Fuel Cell
  133. ^ "Fuel Cell Industry is Poised for Major Change and Development in 2011", Pike Research, February 2, 2011, accessed August 1, 2011
  134. ^ Wesoff, Eric. "Year-End Reflections on the Fuel Cell Industry in 2010". Greentech Media, January 5, 2011, accessed August 3, 2011
  135. ^ "Global Fuel Cell Market by Technology, Application, Component, Installation, Cost, Geography, Trends and Forecasts (2011 – 2016)". May 2011, MarketsandMarkets.com, accessed August 1, 2011
  136. ^ Adamson, Karry-Ann and Clint Wheelock. "Fuel Cell Annual Report 2011". 2Q 2011, Pike Research, accessed August 1, 2011
  137. ^ "Solid State Energy Conversion Alliance SECA Cost Reduction". U.S. Dept. of Energy, January 31, 2011, accessed August 1, 2011
  138. ^ "Lower & Lock-In Energy Costs". Bloom Energy, accessed August 3, 2011
  139. ^ Wesoff, Eric. "Bloom Energy Plays the Subsidy Game Like a Pro", April 13, 2011, accessed August 1, 2011
  140. ^ Faur-Ghenciu, Anca (April/May 2003). Fuel Processing Catalysts for Hydrogen Reformate Generation for PEM Fuel Cells (PDF). FuelCell Magazine. Retrieved 2007-05-27. [dead link]
  141. ^ International Platinum Group Metals Association-FAQ
  142. ^ Johnson, R. Colin (2007-01-22). "Gold is key to ending platinum dissolution in fuel cells". EETimes.com. Retrieved 2007-05-27. 
  143. ^ Replacement of platinum by iron-sulpher
  144. ^ Fuel cell improvements raise hopes for clean, cheap energy
  145. ^ "Chemical Could Revolutionize Polymer Fuel Cells". Georgia Institute of Technology. 2005-08-24. Retrieved 2007-05-27. 
  146. ^ Cheaper fuel cells
  147. ^ Lane, K. (2009, September). Y-carbon? because it has so many applications! NanoMaterials Quarterly, Retrieved from http://www.y-carbon.us/Portals/0/docs/Media/Newsletter_september_2009.pdf
  148. ^ Savage, N. (2009, October). Nanoporous carbon could help power hybrid cars. Technology Review, 112(5), 51, Retrieved from http://www.y-carbon.us/Portals/0/docs/Media/TR35.pdf
  149. ^ Bio-inspired catalyst design could rival platinum

Further reading[edit]

  • Vielstich, W., et al, ed. (2009). Hoboken: John Wiley and Sons.  Text "Handbook of fuel cells: advances in electrocatalysis, materials, diagnostics and durability " ignored (help); Missing or empty |title= (help)
  • Gregor Hoogers (2003). Fuel Cell Technology – Handbook. CRC Press. 
  • James Larminie; Andrew Dicks (2003). Fuel Cell Systems Explained (Second ed.). Hoboken: John Wiley and Sons. 
  • Subash C. Singhal; Kevin Kendall (2003). High Temperature Solid Oxide Fuel Cells-Fundamentals, Design and Applications. Elsevier Academic Press. 
  • Frano Barbir (2005). PEM Fuel Cells-Theory and Practice. Elsevier Academic Press. 
  • EG&G Technical Services, Inc. (2004). Fuel Cell Technology-Handbook, 7th Edition. U.S. Department of Energy. 
  • Matthew M. Mench (2008). Fuel Cell Engines. Hoboken: John Wiley & Sons, Inc. 
  • Noriko Hikosaka Behling (2012). Fuel Cells: Current Technology Challenges and Future Research Needs (First ed.). Elsevier Academic Press. 

External links[edit]

Fuel cells
By electrolyte
By fuel
Biofuel cells
Others
Hydrogen
Types
Galvanic cell
Cell parts
Retrieved from "http://en.wikipedia.org/w/index.php?title=Fuel_cell&oldid=561601520"